The video player is blocked until cookies are accepted.
Watch on VimeoVideo transcript
Download PDFIn this video I plan to explain the different modes available in the Quantum Configurator. The modes vary slightly between the single color configurator and the dual, tri and quad color configurators. I'll start off by explaining the single color configurator modes. For starters, there are 11 available modes. Tail, cruise, front flashing, rear flashing, turn signal, break signal, left alley, right alley, right alley, take down and cut off. Now for the most part, those modes should be pretty self-explanatory. You have multiple flashing modes, some steady on functions, turn, signal, tail, left alley, right alley are single function modes that we broke up to individual tabs, along with your cutoff that disables modules depending on the input you wish to associate that with. In the dual, tri or quad color configurator, the modes are a little bit different. Once you have your bar configured you can move on to that next step and select those inputted modes. Right away you will notice the mode list varies so slightly from single color. There's nine available functions for you. Tail mode, cruise mode, front flashing, rear flashing, arrow directional, turn signal, brake signal, front or rear or side flood, and of course cutoff. Every one of these modes are programmable based on how you wish to activate every module. In later videos, I'll explain in detail every function in every mode and how to configure those functions. Depending on the mode, you will have to associate a few extra functions such as patterns or even brightness level. This concludes the available modes fanned with a single color or multi-color configurator.
Every course on the shelf
Quantum
Quantum 2.0
24 classes · 1 hr 4 min-
1:08
Intro
Introduction to Quantum 2.0
-
1:50
Unboxing
What Comes With the Pillar & Spoiler Mount
-
2:38
Unboxing
What Comes with the 44”, 49” & 60” Lightbars
-
1:42
Unboxing
What Comes With the 12”, 18” & 27” Mini Lightbars
-
3:01
Unboxing
What Comes With the 400, 600, 800 & Rocker Panels
-
2:10
Unboxing
What Comes With the Inner Lightbar
-
0:53
Unboxing
What Comes with the Split and Full Arrow Bar
-
2:50
Install & Wiring
How to Wire & Service Spoiler and Pillar
-
2:41
Install & Wiring
How to Wire & Service 44”, 49” & 60” Lightbars
-
3:35
Install & Wiring
How to Wire & Service 12”, 18” & 27” Mini Lightbar
-
1:52
Install & Wiring
How to Wire & Service Inner Lightbar
-
2:11
Install & Wiring
How to Wire & Service Split and Full Arrow Bar
-
2:54
Programming
How to Upgrade Color Levels
-
3:22
Programming
How to Configure the Color Settings
-
4:34
Programming
How to Program Different Functions
-
3:30
Programming
How to Use the Quantum Converter
-
2:35
Programming
How to Program Flash Mode
-
3:02
Programming
How to Program Directional Mode
-
3:11
Programming
How to Program Cruise Mode
-
3:22
Programming
How to Program Flood Mode
-
4:16
Programming
How to Program Stop-Turn-Tail Mode
-
2:04
Programming
How to Program Cut Off
-
1:37
Programming
How to Program Low Power
-
2:42
Programming
How to Program Pattern Changer
Quantum Software
11 classes-
Overview
The Difference With Dealer and End User Accounts
-
Programming
How to Upgrade to Dual, Tri or Quad
-
Overview
Single, Dual, Tri and Quad Configurator
-
Programming
How to Use Active-Input
-
Overview
What Are the Different Modes
-
Programming
How to Program Tail, Turn and Brake
-
Programming
How to Program Flashing Mode
-
Programming
How to Program Cruise Mode
-
Programming
How to Program Flood Mode
-
Programming
How to Program Arrow Mode
-
Programming
How to Program Cut Off
Q Series
Q Series
22 classes · 48 min-
2:32
Intro
Introduction to the Q Series Family
-
2:46
Install & Wiring
Comparing 3 Mode & Serial Wiring and Installation
-
1:26
Programming
How to Program Q Series Warning Flash Patterns
-
2:41
Programming
How to Program Q Series Pattern Phasing
-
1:09
Programming
How to Program Q Series Cruise Mode
-
2:56
Programming
How to Program Q Series STT Signal
-
1:28
Programming
How to Program Q Series Flood Mode
-
2:34
Programming
How to Program Q Series Colors
-
2:13
Programming
How to Program Q Series Color Lock
-
5:25
Programming
How to Program Q Serial Zones
-
2:35
Programming
How to Program Q Serial Inputs
-
1:35
Programming
How to Program Q Serial Flash Patterns
-
1:52
Programming
How to Program Q Serial Cruise Mode
-
4:07
Programming
How to Program Q Serial Stop-Tail-Turn Signal
-
1:33
Programming
How to Program Q Serial Flood Mode
-
1:24
Programming
How to Program Q Serial Low Power & Cut Off
-
3:04
Programming
How to Program Q Serial Directional Patterns
-
1:58
Unboxing
What Comes with the Q Series Surface Mounts
-
1:11
Unboxing
What Comes with Q Series 100 & 200 Sticks
-
0:54
Unboxing
What Comes with Q Series Mirror Mounts
-
1:55
Unboxing
What Comes with Q Series 1x & 2x Dash Lights
-
1:07
Unboxing
What Comes with Q Series Under Mirror Pucks
