The video player is blocked until cookies are accepted.
Watch on VimeoVideo transcript
Download PDFIn this video, I'll explain how to program front flashing versus rear flashing using tri-color as my example. For starters, you'll notice in front flashing, you're only given the modules located in front of the bar. While in rear flashing, you're given the modules located in the rear of the bar. I'll start with front flashing as my example. For starters, actually, I need to select an input, then front flashing. I can select my pattern that I wish to activate and the intensity. Once all that's done, I then select the module that I wish to activate. I'm given the choice of the three colors I selected in the previous step. Only those three colors will become available to me. I can select one color to flash in a module, I can select two colors, or I can select all three colors to flash with that front flashing mode. The same applies for rear flashing. I can keep rear flashing on the same input to activate them both at the same time, or I can apply rear flashing on a different input so that they're isolated from one another. Once I click rear flashing I select my pattern, my brightness level, and the module that I wish to activate. I'm given the choice of the three colors that I previously set in the first step. Red, blue, or amber are now available to me. I can select all three, just one, or even two colors if I wish to. And of course, once my bar is fully configured, I can then click program device. It takes a few seconds here for your light bar to be programmed. And don't forget, you also have the ability to save your build or upload a pre-built configuration to save you time. That concludes the video of how to associate a module with front flashing or rear flashing flash patterns.
Every course on the shelf
Quantum
Quantum 2.0
24 classes · 1 hr 4 min-
1:08
Intro
Introduction to Quantum 2.0
-
1:50
Unboxing
What Comes With the Pillar & Spoiler Mount
-
2:38
Unboxing
What Comes with the 44”, 49” & 60” Lightbars
-
1:42
Unboxing
What Comes With the 12”, 18” & 27” Mini Lightbars
-
3:01
Unboxing
What Comes With the 400, 600, 800 & Rocker Panels
-
2:10
Unboxing
What Comes With the Inner Lightbar
-
0:53
Unboxing
What Comes with the Split and Full Arrow Bar
-
2:50
Install & Wiring
How to Wire & Service Spoiler and Pillar
-
2:41
Install & Wiring
How to Wire & Service 44”, 49” & 60” Lightbars
-
3:35
Install & Wiring
How to Wire & Service 12”, 18” & 27” Mini Lightbar
-
1:52
Install & Wiring
How to Wire & Service Inner Lightbar
-
2:11
Install & Wiring
How to Wire & Service Split and Full Arrow Bar
-
2:54
Programming
How to Upgrade Color Levels
-
3:22
Programming
How to Configure the Color Settings
-
4:34
Programming
How to Program Different Functions
-
3:30
Programming
How to Use the Quantum Converter
-
2:35
Programming
How to Program Flash Mode
-
3:02
Programming
How to Program Directional Mode
-
3:11
Programming
How to Program Cruise Mode
-
3:22
Programming
How to Program Flood Mode
-
4:16
Programming
How to Program Stop-Turn-Tail Mode
-
2:04
Programming
How to Program Cut Off
-
1:37
Programming
How to Program Low Power
-
2:42
Programming
How to Program Pattern Changer
Quantum Software
11 classes-
Overview
The Difference With Dealer and End User Accounts
-
Programming
How to Upgrade to Dual, Tri or Quad
-
Overview
Single, Dual, Tri and Quad Configurator
-
Programming
How to Use Active-Input
-
Overview
What Are the Different Modes
-
Programming
How to Program Tail, Turn and Brake
-
Programming
How to Program Flashing Mode
-
Programming
How to Program Cruise Mode
-
Programming
How to Program Flood Mode
-
Programming
How to Program Arrow Mode
-
Programming
How to Program Cut Off
Q Series
Q Series
22 classes · 48 min-
2:32
Intro
Introduction to the Q Series Family
-
2:46
Install & Wiring
Comparing 3 Mode & Serial Wiring and Installation
-
1:26
Programming
How to Program Q Series Warning Flash Patterns
-
2:41
Programming
How to Program Q Series Pattern Phasing
-
1:09
Programming
How to Program Q Series Cruise Mode
-
2:56
Programming
How to Program Q Series STT Signal
-
1:28
Programming
How to Program Q Series Flood Mode
-
2:34
Programming
How to Program Q Series Colors
-
2:13
Programming
How to Program Q Series Color Lock
-
5:25
Programming
How to Program Q Serial Zones
-
2:35
Programming
How to Program Q Serial Inputs
-
1:35
Programming
How to Program Q Serial Flash Patterns
-
1:52
Programming
How to Program Q Serial Cruise Mode
-
4:07
Programming
How to Program Q Serial Stop-Tail-Turn Signal
-
1:33
Programming
How to Program Q Serial Flood Mode
-
1:24
Programming
How to Program Q Serial Low Power & Cut Off
-
3:04
Programming
How to Program Q Serial Directional Patterns
-
1:58
Unboxing
What Comes with the Q Series Surface Mounts
-
1:11
Unboxing
What Comes with Q Series 100 & 200 Sticks
-
0:54
Unboxing
What Comes with Q Series Mirror Mounts
-
1:55
Unboxing
What Comes with Q Series 1x & 2x Dash Lights
-
1:07
Unboxing
What Comes with Q Series Under Mirror Pucks
